http://ndgarrison.com/ndforum/ |
|
Up grading my bucket http://ndgarrison.com/ndforum/viewtopic.php?f=6&t=355 |
Page 5 of 9 |
Author: | Ruck [ Mon Nov 25, 2013 11:04 pm ] |
Post subject: | Re: Up grading my bucket |
The battery boxes each have an on/off switch marked with the green circles. |
Author: | Ruck [ Mon Nov 25, 2013 11:21 pm ] |
Post subject: | Re: Up grading my bucket |
So if you don't make sure all the components are in the on position the system won't work, if you don't have the volume control adjusted you won't get any sound. So you get all this calibrated before you put it the bucket cause it's so much easier that way. Once you install everything inside the lid, and all the components are on, flip on the master power switch and adjust the master volume control and the helmet comes to life!!! You can hear fingers lightly rubbed together from across the room very clearly its amazing!!! be careful at first cause you'll think you want that sound up but the first time someone makes a load noise, WOW you'll turn it down lol. |
Author: | Ruck [ Mon Nov 25, 2013 11:52 pm ] |
Post subject: | Re: Up grading my bucket |
Author: | Ruck [ Mon Nov 25, 2013 11:58 pm ] |
Post subject: | Re: Up grading my bucket |
Well there you have it, part 1 to my build, "The sound system" and "Padding". Part 2 soon to follow, "The Fans part 1". Stay tuned to the Ruck show for our exciting new episodes. |
Author: | Ruck [ Tue Dec 03, 2013 10:12 pm ] |
Post subject: | Re: Up grading my bucket |
Author: | Ruck [ Tue Dec 03, 2013 10:19 pm ] |
Post subject: | Re: Up grading my bucket |
Once I had the housings trimmed I needed to make cages for each fan. |
Author: | Ruck [ Tue Dec 03, 2013 10:25 pm ] |
Post subject: | Re: Up grading my bucket |
I found a file folder holder at Walmart that had the metal mesh I was looking for and was black, I measured the fans width and length to get the size I needed. I also added length so I had tabs that would hold the fans to my bucket. |
Author: | Ruck [ Tue Dec 03, 2013 10:27 pm ] |
Post subject: | Re: Up grading my bucket |
Author: | Ruck [ Tue Dec 03, 2013 10:31 pm ] |
Post subject: | Re: Up grading my bucket |
Once I got the measurement for the size of the piece I would need I took a ruler and pencil and drew lines on the mesh. I took my dremel with a metal cutting disc and cut out the piece I needed. |
Author: | Ruck [ Tue Dec 03, 2013 10:33 pm ] |
Post subject: | Re: Up grading my bucket |
Just a little taste for now, stay tuned for the further adventures of the Ruck Show!! |
Author: | Ruck [ Thu Dec 05, 2013 10:37 pm ] |
Post subject: | Re: Up grading my bucket |
Hey Brad I just received the padding, a typical bucket takes four pads one on top, one in back, and one on each side. You just trim out what you don't need but unless your putting stuff in your bucket you wont have to trim any off they fit perfectly. I chose not to glue them in, I used industrial Velcro that way I could adjust them as needed. |
Author: | Ruck [ Thu Dec 05, 2013 10:47 pm ] |
Post subject: | Re: Up grading my bucket |
Once I cut the piece out I then took the dremel and used the flat side like a sanding wheel and sanded the edges. They will be sharp so you want to dull them down a little. |
Page 5 of 9 | All times are UTC - 6 hours [ DST ] |
Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |